How to Reset Govee LED Lights (8 Tips you need to Know)

Govee is a brand noted for producing high-quality LED lights in a variety of shapes and sizes. While most Govee lights have a built-in reset mechanism, there may be situations when you need to manually reset them. For example, if you have ever had problems with your Govee LED lights, such as the light not coming on or flickering, you may need to reset the lights.

This blog post will lead you through the steps of manually how to Reset Govee LED Lights

To begin, make sure the light is turned off and disconnected. Then, for around 10 seconds, hold down the power button until the light starts blinking. Finally, depress the button and connect the light. The light should now be adjusted and operational. Continue reading for more information.

Table of Contents

Can Govee Led Lights Be Reset?

Resetting Govee Led Lights is a straightforward procedure that may be completed in a few simple steps. To begin, turn off the lights and disconnect them from any power sources. Then, for 10 seconds, push and hold the reset button with a small object such as a paper clip. Finally, reconnect the lights and re-turn on the power.

Resetting your Govee Led Lights will help you fix problems like flashing or flickering, unexpected colour changes, and an unresponsive remote control. Resetting the lights on a regular basis might also help to ensure that they continue to work properly. So, don’t be afraid to reset your Govee Led Lights when necessary – it’s a simple solution to any troubles you may have.

How to Reset Govee Led Lights Step by Step

Step 1: Disconnect the Light Strip from the Power Supply.

The first step is to unplug the light strip from the power supply. After unplugging it, press and hold the reset button for 3 seconds; make sure the reset button is held down for 3 seconds. If your light strip lacks a reset button, simply remove the batteries for around 10 seconds before replacing them.

Step 2: Verify If the Controller Is Active

The next step is to ensure that the controller is operational. You can test this by plugging in the light strip and seeing if it turns on. Check that the controller is also turned on. If the light strip does not turn on, the controller must be replaced. Check the controller’s functionality by pushing the button on the controller. If the light strip does not turn on, the controller must be replaced.

Step 3: Trim the Light Strip’s End

If your light strip is still not working after completing the preceding instructions, you may need to cut it off and reattach it. Check that the cut-off end is properly connected to your light strip. If your light strip lacks a connector, you can attach the wires directly to the board. Check that the + and – wires are connected to the correct board pads and that there are no loose connections.

Step 4: Attach the Power Connector

You can now connect the power connector to the light strip. Before connecting the power connector, be sure it is pointing in the right direction. Plug in your light strip’s power adapter if it has one. The light strip will not work if the power connector is not oriented correctly. By hitting the controller’s button, you may see if the light strip is operating. If the light strip does not turn on, the controller must be replaced.

Step 5: Check that the remote works properly.

If you’re using a remote to control your Govee LED light strip, make sure it’s in good working order. Simply press and hold the power button on the remote for 3 seconds to accomplish this. If the light strip does not turn on, the remote must be replaced. Check the batteries in the remote and make sure they are correctly fitted.

Step 6: Hold the Reset Button.

If your light strip still does not function, try resetting it by pushing and holding the reset button for 3 seconds. When you release the reset button, the light strip should start working again. If your light strip lacks a reset button, simply remove the batteries for around 10 seconds before replacing them. The light strip should be reset as well. If the light strip still does not function, it is most likely defective and must be replaced.

Step 7: Verify that the light strip is flashing.

There is a problem with the connection if the light strip flashes. Before connecting the power connector, be sure it is pointing in the right direction. Plug in your light strip’s power adapter if it has one. The light strip will not work if the power connector is not oriented correctly. Make sure the power adapter is inserted into the proper outlet. If it is, unplug it and reconnect it.

If the light strip continues to flash, there may be a problem with it. The light strip can be reset. To begin, unplug the power adapter from the outlet. Check that the light strip’s power connector is not attached. Hold the reset button for a few seconds. The LEDs will illuminate and the light strip will be reset.

Step 8: Replace the Light Strip

If your light strip is still not working, it is most likely defective and must be replaced. A new light strip can be purchased from Gove’s website or a shop. To properly install the new light strip, follow the directions in the user handbook. Before attempting to change the light strip, make sure the power is switched off. Please contact Gove’s customer service department if you have any queries or issues.

They would gladly assist you in troubleshooting and resolving the problem. If you have any more questions or issues, please contact us at any time. We are always willing to assist! Thank you for deciding on Govee!

How to factory reset Govee LED lights

Here are steps of How to factory reset Govee LED lights

Using the remote control:
Hold down the power button on the remote while hitting the centre Colour Mode button four times.
Using the Govee Home app:
Launch the Govee Home app and pick the light you want to reset. Scroll down and press the “Delete” button. Then click “OK” to confirm your action. This will return the lamp to its default settings.
Using the control box:
Turn on the strip lighting, then repeatedly press the control box’s centre switch to return the strip lighting to its default settings.

It’s crucial to note that the exact steps will differ based on the model of Govee LED lights you have.

How to Troubleshoot Govee Led Lights

If your Govee Led Lights are not operating properly, they may need to be reset. Follow these steps to accomplish this:

1. Take the power adapter out of the wall outlet.

2. Remove the remote control’s batteries.

3. For 5 seconds, press and hold the power button on the back of the Govee Led Light.

4. Replace the batteries in the remote control and reconnect the power adapter to the wall socket.

5. To switch on the Govee Led Lights, press the power button on the remote control.

The lights should now be working properly. However, if you continue to have problems, please contact customer service.

What Should You Do If Your Govee Led Strip Isn’t Working?

If your Govee LED strip stops working, there are a few things you can attempt to reset it. Sometimes simply unplugging the strip and plugging it back in will be enough. If it doesn’t work, you can try resetting the strip by holding down the power button for 5-10 seconds. If nothing of these options works, you may need to replace the LED strip.

Before you begin, double-check the following items:

1. Check that the power source is properly connected to the strip and hooked into an outlet.

2. Check that the controller is properly attached to the strip.

3. Check for any loose connections between the power supply, controller, and strip.

4. If your Govee LED strip is still not working after testing these things, try resetting it by holding the power button for 5-10 seconds. Even if this don’t work replace the LED srtip.

How Do Pair Govee Led Light?

To pair the Govee Led, do the following:

1. Press and hold the power button on the back of the Govee Led for 3 seconds.

2.The Govee Led will enter pairing mode, and the indicator light will flash rapidly.

3. Once the Govee Led is in pairing mode, connect it to your device through Bluetooth.

4.Once the Govee Led is linked to your smartphone, you may begin utilising it.

How to reset govee rgb led strip lights

Conclusion:

If you’re having problems with your Govee lights, resetting them might be the answer. Though resetting your Govee Led Lights may appear difficult, it is a simple operation. Furthermore, if your lights are not working properly, restarting them would most likely resolve the problem.

You’ll be able to have your lights back up and running in no time if you follow the instructions provided in this blog post on how to reset Govee led lights. So, the next time your lights stop working properly, don’t panic – just follow these simple procedures and you’ll be OK! We hope you found this Information valuable and comment your Questions down Below.

Featured Image Credits: Digitaltrends.com